EPRO PR937620前置電纜,PR937620使用數據
設備連接單板計算機中有一些連接圖程序員參考指南。
MVME712X轉換模塊和P2適配器板連接MVME187的外圍設備如表3-10所示?？刂婆_終端、主機系統、調制解調器或串行打印機上的EIA-232-D串行端口過渡模塊上的并行打印機Centronics打印機端口過渡模塊可選內部調制解調器（請參閱過渡用戶手冊詳細信息模塊）
EPRO PR937620前置電纜可選調制解調器端口，替換串行端口過渡模塊上的端口2內部SCSI驅動器適配器板和轉換模塊上的外部SCSI驅動器SCSI接口連接器過渡模塊以太網連接過渡模塊上的以太網端口在過渡模塊上設置跳線模塊并安裝SCSIP2上的終端（如需要）適配器板。
用戶手冊中的模塊準備過渡模塊手冊和適配器板SCSI總線終端，第3-29頁2連接并安裝MVME712X前部的過渡模塊或機箱后部。
用戶手冊中的安裝說明過渡模塊手冊和適配器板3連接并安裝? 位于上的P2接頭MVME187處的背板狹槽用戶手冊中的安裝說明過渡模塊手冊和適配器板? 來自P2的SCSI電纜
適配器板至MVME712X過渡模塊和內部SCSI設備。用戶手冊中的模塊準備過渡模塊手冊適配器板和SCSI總線第3-29頁連接外圍設備上的終端MVME187與（可選）終端或其他外圍設備配套在EIA-232-D串行端口（標記為串行端口1、2、3和4在MVME712X轉換模塊上）、并行端口、SCSI端口、，和LAN以太網端口，如第3-22頁圖3-3所示。
注：MVME712X未提供一些電纜模塊，因此由使用者（摩托羅拉建議使用屏蔽電纜所有與外圍設備的連接，以盡量減少輻射。）
Equipment Connections
Some connection diagrams are in the Single Board Computer
Programmer's Reference Guide.
The MVME712X transition modules and P2 adapter boards connect
peripheral equipment to the MVME187 as shown in Table 3-10.Console terminals, host computer
systems, modems, or serial printers
EIA-232-D serial ports on the
transition module
Parallel printers Centronics printer port on the
transition module
Optional internal modems (see the
user’s manual for your transition
module for details)
Optional modem port, replacing serial
port 2 on the transition module
Internal SCSI drives Adapter board and transition module
External SCSI drives SCSI interface connector on the
transition module
Ethernet connections Ethernet port on the transition moduleSet jumpers on the transition
module(s) and install SCSI
terminators (if needed) on the P2
adapter board.
Module Preparation in the user’s
manual for your transition module
and adapter board, and
SCSI Bus Termination on page 3-29
2 Connect and install the MVME712X
transition module in the front or the
rear of the chassis.
Installation Instructions in the user’s
manual for your transition module
and adapter board
3 Connect and install
? The P2 adapter board at the
P2 connector on the
backplane at the MVME187
slot.
Installation Instructions in the user’s
manual for your transition module
and adapter board
? SCSI cable(s) from the P2
adapter board to the
MVME712X transition
module and internal SCSI
devices.
Module Preparation in the user’s
manual for your transition module
and adapter board, and SCSI Bus
Termination on page 3-29Connecting Peripherals
The MVME187 mates with (optional) terminals or other peripherals
at the EIA-232-D serial ports (marked SERIAL PORTS 1, 2, 3, and 4
on the MVME712X transition module), parallel port, SCSI ports,
and LAN Ethernet port, as shown in Figure 3-3 on page 3-22.
Note Some cable(s) are not provided with the MVME712X
module(s), and therefore are made or provided by the
user. (Motorola recommends using shielded cables for
all connections to peripherals to minimize radiation.)
