產品內容介紹
A-B 80190-920-03-R脈沖驅動控制
上傳電子版數據表（EDS）文件
選件模塊嵌入了PowerFlex 750系列驅動器的EDS文件。
這樣就無需從Rockwell下載EDS文件自動化網站。相反，RSLinx軟件用于上傳EDS文件來自選項模塊。
為此，右鍵單擊EtherNet/IP驅動器在RSWho中顯示為黃色問號或“無法識別的設備”對話框并選擇“從設備上載EDS文件”，如下所示。
正在上載EDS文件還上載設備的圖標文件。問號將更改為驅動器（在適配器模式下）或eTap（在Tap模式下）。ControlLogix控制器
示例（適配器模式僅限）
配置選項模塊后，驅動器和選項模塊將是單個網絡(luò )上的節點。
本節提供了配置簡單設備級環（DLR）拓撲EtherNet/IP網絡(luò )（見圖10）。
我們的例如，我們將配置一個1756-EN2TR（a系列）網橋來與網絡(luò )環中使用邏輯命令/狀態的第一個驅動器，參考/反饋和32個數據鏈路（16個用于讀取，16個用于寫入）。
要在控制器和選項模塊之間通過網絡(luò )，必須首先將ControlLogix控制器及其網橋添加到I/O配置。
1.啟動RSLogix 5000軟件。
2.從文件菜單中，選擇新建以顯示新建控制器對話框盒a、 為對話框中要匹配的字段選擇適當的選項您的應用程序。
b、 單擊“確定”。RSLogix 5000對話框重新出現，樹視圖位于左側窗玻璃
3.在樹視圖中，右鍵單擊I/O配置文件夾，然后選擇新建單元單擊更改以更改修訂或電子鍵控。
網橋中固件的次要修訂。
（您已經設置了主要修訂通過在步驟5中選擇橋系列。）兼容模塊。
電子鑰匙的“兼容模塊”設置驗證物理模塊是否與之前的軟件配置一致控制器和網橋連接。
請確保已將在此對話框中更正修訂。
有關的其他信息，請參閱聯機幫助此設置和其他電子鍵控設置。
如果不需要鍵入，請選擇“禁用鍵控?！苯ㄗh禁用鍵控。
使用RSLogix 5000驅動器附加配置文件，版本16.00或更高版本與使用通用配置文件（所有版本）相比，RSLogix 5000
驅動器附加配置文件具有以下優點：
?為基本驅動器提供描述性控制器標簽的特定驅動器的配置文件控制I/O字（邏輯命令/狀態和參考/反饋）和數據鏈接。
此外，Datalinks會(huì )自動使用分配給它們的驅動器參數。
這些配置文件實際上I/O不匹配錯誤并大幅減少驅動器配置時間。
?新的驅動器選項卡無需單獨的驅動器軟件配置工具。
?驅動器配置設置保存為RSLogix 5000的一部分軟件，版本16.00或更高版本，項目文件（.ACD），還下載了到控制器。
Uploading the Electronic Data Sheet (EDS) File
The option module has embedded EDS files for PowerFlex 750-Series drives. This eliminates the need to download an EDS file from the Rockwell Automation website. Instead, RSLinx software is used to upload the EDS file from the option module. To do this, right-click the EtherNet/IP drive that is shown as a yellow question mark or “Unrecognized Device” in the RSWho dialog box and choose “Upload EDS file from device” as shown below. Uploading the EDS file also uploads the icon files for the device. The question mark will change to a drive (in Adapter mode) or an eTap (in Tap mode). ControlLogix Controller Example (Adapter mode only) After the option module is configured, the drive and option module will be a single node on the network. This section provides the steps needed to configure a simple device-level ring (DLR) topology EtherNet/IP network (see Figure 10). In our example, we will configure a 1756-EN2TR (Series A) bridge to communicate with the first drive in the network ring using Logic Command/Status, Reference/ Feedback, and 32 Datalinks (16 to read/16 to write) over the network.To establish communication between the controller and option module over the network, you must first add the ControlLogix controller and its bridge to the I/O configuration. 1. Start RSLogix 5000 software. 2. From the File menu, choose New to display the New Controller dialog box.a. Choose the appropriate choices for the fields in the dialog box to match your application. b. Click OK. The RSLogix 5000 dialog box reappears with the treeview in the left pane. 3. In the treeview, right-click the I/O Configuration folder and choose New Module.
Using RSLogix 5000 Drive Add-on Profiles, Version 16.00 or Later
When compared to using the Generic Profile (all versions), the RSLogix 5000 drive Add-on Profiles provide the following advantages: ? Profiles for specific drives that provide descriptive controller tags for basic control I/O words (Logic Command/Status and Reference/Feedback) and Datalinks. Additionally, Datalinks automatically take the name of the drive parameter to which they are assigned. These profiles virtually eliminate I/O mismatch errors and substantially reduce drive configuration time. ? New Drive tab eliminates the need for a separate drive software configuration tool. ? Drive configuration settings are saved as part of the RSLogix 5000 software, version 16.00 or later, project file (.ACD) and also downloaded to the controller.
Click Change to change Revision or Electronic Keying. The minor revision of the firmware in the bridge. (You already set the major revision by selecting the bridge series in step 5.) Compatible Module. The “Compatible Module” setting for Electronic Keying verifies that the physical module is consistent with the software configuration before the controller and bridge make a connection. Therefore, be sure that you have set the correct revision in this dialog box. See the online Help for additional information on this and other Electronic Keying settings. If keying is not required, select “Disable Keying.” Disable keying is recommended.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
