產品內容介紹
A-B 8510-AA22-B2模擬量伺服控制器
ControlLogix控制器–說明圖36和圖37中的數據結構使用32位字，可以在一條消息中最多可容納32個參數。在響應消息中，設置了位15的參數編號表示相關參數值字段包含錯誤代碼（響應數據中的參數編號將為負數）。
PowerFlex 750系列交流驅動器編程手冊，出版物750-PM001列出了每個參數的數據類型。執行散射時讀取REAL數據類型參數，響應中的DINT參數（目標數據）數組需要COP到REAL標記。驅動器處于固件升級模式。
選項模塊存在EEPROM故障。
網絡(luò )地址開關在通電后已更改。
檢測到重復的IP地址故障。DHCP租約已過期。
網絡(luò )地址開關設置為“888”
網絡(luò )配置（IP地址、子網掩碼、網關地址）無效。用戶FPGA配置無效。
查看選項模塊事件隊列以確定這些條件中的哪些是目前然后，根據原因，采取適當的糾正措施。
?清除選項模塊中的故障。
?循環驅動電源。
?如果循環電源不能解決問題，則選項模塊參數
設置可能已損壞。重置默認值并重新配置選項單元
?如果重置默認值不能解決問題，請更新選項模塊具有最新固件版本。
?將網絡(luò )地址開關更改為“888”以外的值。糾正措施
關閉選項模塊未通電。
選項模塊未正確連接到網絡(luò )。
選項模塊尚未獲取其網絡(luò )配置（IP地址、子網掩碼、網關地址）服務器
?將選件模塊完全連接并接地至驅動器
將其插入驅動器端口，并將其兩個外加螺釘擰緊至建議扭矩。
?將以太網電纜正確連接到以太網連接器。
?使用選項模塊旋轉開關設置唯一的IP地址，選項模塊參數，或BOOTP或DHCP服務器。
?給驅動器通電。
紅色閃爍I/O連接超時。?將控制器置于RUN模式，或向對等設備通電發送I/O。
?檢查IGMP偵聽/以太網交換機是否正常工作。
?檢查網絡(luò )流量。
穩定紅色檢測到重復的IP地址故障。DHCP租約已過期。配置選項模塊以使用唯一的IP地址并循環電源。
綠色閃爍選項模塊工作正常，但沒有CIP連接（I/O或顯式）。
?將控制器置于RUN模式，或向對等設備通電發送I/O。
?對控制器或對等設備進行編程，以識別和傳輸I/O，或與選項模塊的消息連接。
?為控制器或I/O中的程序配置選項模塊來自對等設備。
ControlLogix Controller – Explanation
The data structures in Figure 36 and Figure 37 use 32-bit words and can accommodate up to 32 parameters in a single message. In the Response Message, a parameter number with Bit 15 set indicates that the associated parameter value field contains an error code (parameter number in response data will be negative). The PowerFlex 750-Series AC Drives Programming Manual, publication 750-PM001, lists the data type for each parameter. When performing a Scattered Read of REAL data type parameters, the DINT parameter value in the Response (Destination Data) array will need to be COP to a REAL tag.The drive is in firmware upgrade mode. The option module has an EEPROM fault. The network address switches have been changed since powerup. A duplicate IP address fault has been detected. The DHCP lease has expired. The network address switches are set to “888.” The network configuration (IP address, subnet mask, gateway address) is invalid. The User FPGA configuration is invalid. View the option module event queue to determine which of these conditions is present. Then, depending on the cause, take the appropriate corrective action. ? Clear faults in the option module. ? Cycle power to the drive. ? If cycling power does not correct the problem, the option module parameter settings may have been corrupted. Reset defaults and reconfigure the option module. ? If resetting defaults does not correct the problem, update the option module with the latest firmware revision. ? Change the network address switches to a value other than “888.”
Corrective Actions Off
The option module is not powered. The option module is not properly connected to the network. The option module has not acquired its network configuration (IP address, subnet mask, gateway address) from the BOOTP/DHCP server. ? Securely connect and ground the option module to the drive by fully inserting it into the drive port and tightening its two captive screws to the recommended torque. ? Correctly connect the Ethernet cable to the Ethernet connector. ? Set a unique IP address with the option module rotary switches, option module parameters, or a BOOTP or DHCP server. ? Apply power to the drive. Flashing Red The I/O connection has timed out. ? Place the controller in RUN mode, or apply power to the peer device that will send I/O. ? Check the IGMP Snooping/Ethernet Switches for correct operation. ? Check the amount of traffic on the network. Steady Red A duplicate IP address fault has been detected. The DHCP lease has expired. Configure the option module to use a unique IP address and cycle power. Flashing Green The option module is operating normally, but does not have any CIP connections (I/O or explicit). ? Place the controller in RUN mode, or apply power to the peer device that will send I/O. ? Program the controller or peer device to recognize and transmit I/O, or make a message connection to the option module. ? Configure the option module for the program in the controller or the I/O from the peer device.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
