產品內容介紹
EMERSON 01984-2347-0021主驅動器控制卡
本章的前幾頁提供了獨立于模塊的內容
關于設置節點編號、機械安裝和ACS 600連接。模塊特定說明（例如I/O和電源連接）。
設置模塊節點編號
每個模塊必須有一個單獨的節點號。節點數字是通過調整位于頂蓋下的DIP開關來設置的模塊外殼（見左下圖）。每個的開關設置模塊如下所示。對于允許的NDIO和NAIO節點數字，請參閱驅動器的固件手冊。機械安裝根據驅動器的不同，模塊可以安裝在內部或驅動器外殼或機柜外部。請參閱的硬件手冊模塊放置選項的驅動器。
外部安裝
驅動器
選擇模塊的位置。請注意以下事項：
?布線說明（本章后面針對每個模塊給出類型）。此外，光纖電纜的長度選項包中包含的選項可能會(huì )限制模塊和驅動器。
?遵守模塊的自由空間要求（最小10 mm與驅動器（參見驅動器文檔）。
?必須考慮環境條件（參見附錄B）。
模塊的防護等級為IP 20。
?模塊接地通過一個接地夾（見下圖3-2）。安裝導軌要安裝的模塊必須接地至無聲接地。如果軌道沒有安裝在正確接地的底座上必須使用接地導體。導線必須同樣短橫截面積必須至少為6 mm2。
注：不得使用實心銅導線（絞合線僅允許）。安裝說明：
1.關閉模塊外殼中的所有危險電壓將安裝在中。
2.緊固導軌并確保如上所述正確接地。
3.將模塊推到導軌上。模塊可以通過以下方式釋放用螺絲刀拉動鎖定彈簧（見圖3-2）。
注意電池的緩慢放電電壓電容器組和從外部連接的電壓驅動器輸入和輸出的控制電路。請勿觸摸印刷電路板。集成的電路對靜電放電極為敏感。
The first few pages of this chapter
provide module-independent instructions on setting the node number, mechanical installation and ACS 600 connection. Module-specific instructions (e.g. on I/O and power connections) are given later in the chapter. Setting the Module Node Number Each module must be given an individual node number. The node number is set by adjusting the DIP switches located under the top lid of the module casing (see picture below left). The switch settings for each module are shown below. For allowable NDIO and NAIO node numbers, see the Firmware Manual of the drive.Mounting instructions: 1. Switch off all dangerous voltages in the enclosure that the module is to be mounted in. 2. Fasten the rail and ensure proper earthing as described above. 3. Push the module onto the rail. The module can be released by pulling the locking spring with a screwdriver (see Figure 3-2).Pay attention to the slowly discharging voltage of the capacitor bank and the voltages that are connected from external control circuits to the inputs and outputs of the drive.Do not touch the printed circuit boards. The integrated circuits are extremely sensitive to electrostatic discharge.
Mechanical Installation
Depending on the drive, the module(s) can be installed either inside or outside the drive housing or cabinet. See the Hardware Manual of the drive for module placement options. Mounting Outside the Drive Choose the location for the module. Note the following: ? The cabling instructions (given later in this chapter for each module type) must be followed. Also, the length of the fibre optic cables included in the option package may restrict the distance between the module and the drive. ? Observe the free space requirements for the module (min. 10 mm from adjoining equipment or wall) and the drive (see the drive documentation). ? The ambient conditions must be taken into account (see Appendix B). The degree of protection of the module is IP 20. ? Module earth is connected to the mounting rail by means of an earthing clip (see Figure 3-2 below). The mounting rail onto which the module is to be mounted must be earthed to a noiseless earth. If the rail is not mounted on a properly earthed base, a separate earthing conductor must be used. The conductor must be as short as possible and the cross-sectional area must be 6 mm2 at least. Note: No solid copper conductor may be used (stranded wire allowed only).
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
