330180-51-CN前置放置器
說明機架接口模塊
（RIM）是3301機架的主要接口。它支持用于配置機架和檢索機器信息的專有協議。RIM必須位于機架的插槽1中（靠近電源）。RIM支持兼容的Bently Nevada外部通信處理器，如TDXnet、TDIX和DDIX。雖然RIM提供了整個機架通用的某些功能，但RIM不是關鍵監控路徑的一部分，不會(huì )影響整個監控系統的正常正常運行。每個機架需要一個RIM。對于三模冗余（TMR）應用，3301系統需要TMR版本的RIM。除所有標準RIM功能外，TMR RIM還執行“監視器通道比較”。3301 TMR配置使用監視器選項中指定的設置實現監視器表決。使用此方法，TMR RIM連續比較三（3）個冗余監視器的輸出。如果TMR RIM檢測到其中一個監測器的信息不再在其他兩個監測器信息的配置百分比內，它將標記監測器出錯，并將事件置于系統事件列表中。3301/20機架接口模塊數據表Bently Nevada機械狀態監測141531 C版規格輸入功耗4.75瓦，典型數據前面板標準RS232串行通信數據速率38.4 k波特。I/O模塊標準RS232/RS422串行通信內部調制解調器通信數據速率最大38.4 k波特，串行通信14.4 k波特、內部調制解調器通信。輸出前面板LED正常LED指示RIM正常工作。TX/RX LED指示RIM何時與3301機架中的其他模塊通信。
TM LED指示
3301機架處于跳閘倍增狀態。CONFIG OK LED指示3301機架具有有效配置。I/O模塊OK（正常）繼電器，用于指示3301機架何時正常運行或機架內檢測到故障。用戶可以選擇“打開”或“關閉”觸點來通知NOT OK狀態。該繼電器始終在“正常通電”狀態下工作。OK繼電器額定值為5A@24 Vdc/120 Vac，120瓦/600 VA開關電源。提供常閉觸點電弧抑制器?？刂魄懊姘鍣C架復位按鈕清除機架中的鎖定報警和定時OK通道失效。執行與I/O模塊上的“機架復位”觸點相同的功能。地址開關用于設置63個可能的機架地址。配置鍵鎖用于將3301機架置于“運行”模式或“編程”模式。運行模式允許機架正常運行并鎖定配置更改。編程模式允許機架正常運行，也允許本地或遠程機架配置。鑰匙可以在任一位置從機架上取下，使開關保持在運行或編程位置。將開關鎖定在RUN（運行）位置允許您限制未經授權的機架重新配置。將開關鎖定在PROGRAM（編程）位置允許隨時遠程配置機架。I/O模塊系統觸點跳閘倍增用于將3301機架置于跳閘倍增。報警抑制用于抑制3301機架中的所有報警。機架復位用于清除鎖定報警和定時OK通道失效。最大電流<1 mA dc，干觸點至公共線。RS232/RS422開關（僅限RS232/RS422 I/O模塊）用于在RS232和RS422之間進行選擇，以便與Bently Nevada主機軟件進行通信。通信前面板通信僅RS232串行通信。本特利內華達專利協議。數據速率最大38.4 k波特（支持自動波特）。用途允許數據采集和3301機架配置。電纜長度最大30米（100英尺）。RS232/RS422輸入/輸出模塊通信RS232、RS422或外部調制解調器。本特利內華達專利協議。波特率最大38.4 k波特率（支持自動波特率）。用途允許數據采集和3301機架配置。
Description Rack Interface Module
(RIM) is the main interface of the 3301 rack. It supports proprietary protocols for configuring racks and retrieving machine information. The RIM must be in slot 1 of the rack (near the power supply). RIM supports compatible Bently Nevada external communication processors such as TDXnet, TDIX, and DDIX. Although RIM provides some functions common to the entire rack, it is not part of the critical monitoring path and will not affect the normal operation of the entire monitoring system. Each rack requires one RIM. For the third mock examination Redundancy (TMR) applications, the 3301 system requires a TMR version of RIM. In addition to all standard RIM functions, the TMR RIM performs a Monitor Channel Comparison. The 3301 TMR configuration uses the settings specified in the Monitor Options to implement monitor voting. Using this method, the TMR RIM continuously compares the outputs of three (3) redundant monitors. If the TMR RIM detects that the information for one of the monitors is no longer within the configured percentage of the information for the other two monitors, it flags the monitor error and places the event in the system event list. 3301/20 Rack Interface Module Data Sheet Bently Nevada Mechanical Condition Monitoring 141531 Version C specification Input power consumption 4.75 watts, typical data front panel standard RS232 serial communication data rate 38.4 k baud. I/O module standard RS232/RS422 serial communication internal modem communication data rate is 38.4 k baud at most, and 14.4 k baud for serial communication and internal modem communication. The output front panel LED indicates that the RIM is working normally. The TX/RX LED indicates when the RIM is communicating with other modules in the 3301 rack.
TM LED indication
The 3301 rack is in Trip Multiply. The CONFIG OK LED indicates that the 3301 rack has a valid configuration. The I/O module OK relay is used to indicate when the 3301 rack is operating normally or a fault is detected in the rack. The user can select "open" or "close" contacts to notify the NOT OK status. The relay always operates in the "normally energized" state. The OK relay is rated as 5A@24 Vdc/120 Vac, 120W/600 VA switching power supply. A normally closed contact arc suppressor is provided. The control front panel rack reset button clears the lock alarm and timed OK channel failure in the rack. Performs the same function as the Rack Reset contact on the I/O module. The address switch is used to set 63 possible rack addresses. The configuration key lock is used to place the 3301 rack in either the RUN mode or the PROGRAM mode. The operating mode allows the rack to operate normally and lock configuration changes. The programming mode allows the rack to operate normally and also allows local or remote rack configuration. The key can be removed from the rack at any position to keep the switch in the run or programmed position. Locking the switch in the RUN position allows you to limit unauthorized rack reconfiguration. Locking the switch in the PROGRAM position allows the rack to be remotely configured at any time. The I/O module system contact trip multiplier is used to place the 3301 rack in the trip multiplier. Alarm Inhibit is used to suppress all alarms in the 3301 rack. Rack reset is used to clear lockout alarms and timed OK channel failures. Maximum current<1 mA dc, dry contact to common. The RS232/RS422 switch (RS232/RS422 I/O modules only) is used to select between RS232 and RS422 for communication with Bently Nevada host software. The communication of the front panel is only RS232 serial communication. Bently Nevada Patent Agreement. The maximum data rate is 38.4 k baud (automatic baud is supported). Purpose Allows data acquisition and 3301 rack configuration. The maximum cable length is 30 meters (100 feet). RS232/RS422 I/O module communication RS232, RS422 or external modem. Bently Nevada Patent Agreement. The maximum baud rate is 38.4 k (automatic baud rate is supported). Purpose Allows data acquisition and 3301 rack configuration.
