TRICONEX 9670-610模塊備件
曲線重要：
所示曲線和性能數據適用于放大器額定值大于或等于電機持續失速電流的電機和組合。在環境中，在的線路電壓下測試電機。外殼溫度約為，電機繞組比環境溫度升高。當電機安裝在×鋼安裝支架上時，確定扭矩額定值。電機包含兩個串聯的熱開關，在超溫條件下打開。溫度設置為±。觸點的額定值為時為，時為。所有值峰值續峰值扭矩電機轉速續峰值峰值，扭矩加系列，交流伺服電機出版物年月和旋轉變壓器和高分辨率電機的
電機速度扭矩曲線重要：
所示曲線和性能數據適用于放大器額定值大于或等于電機持續失速電流的電機和組合。在環境中，在的線路電壓下測試電機。外殼溫度約為，電機繞組比環境溫度升高。當電機安裝在×鋼安裝支架上時，確定扭矩額定值。電機包含兩個串聯的熱開關，在超溫條件下打開。溫度設置為±。觸點的額定值為時為，時為。下面顯示的所有值的公差為±。類別參數環境溫度單位一般連續失速扭矩時的。持續失速電流時的安培峰值失速電流下的安培時的機械時間常數下的電氣時間常數額定轉速時的熱最高環境溫度無降額℃絕緣等級熱時間常數分鐘。
Curves are important:
The curves and performance data shown are for motors and combinations with amplifier ratings greater than or equal to the continuous stall current of the motor. In the environment, test the motor at line voltage of. The enclosure temperature is about, and the motor winding temperature is higher than the ambient temperature. When the motor is installed on the × Determine the torque rating when mounting on a steel bracket. The motor contains two thermal switches in series, which open under overtemperature conditions. The temperature is set to ±. The contact is rated when is and when is. All values peak value followed by peak torque motor speed followed by peak value, torque plus series, AC servo motor publications, and resolver and high-resolution motor
Motor speed torque curve is important:
The curves and performance data shown are for motors and combinations with amplifier ratings greater than or equal to the continuous stall current of the motor. In the environment, test the motor at line voltage of. The enclosure temperature is about, and the motor winding temperature is higher than the ambient temperature. When the motor is installed on the × Determine the torque rating when mounting on a steel bracket. The motor contains two thermal switches in series, which open under overtemperature conditions. The temperature is set to ±. The contact is rated when is and when is. All values shown below have a tolerance of ±. Category parameter Ambient temperature unit is generally at continuous stall torque. Ampere at continuous stall current, peak value at stall current, mechanical time constant at ampere hour, electrical time constant at rated speed, maximum thermal ambient temperature without derating ℃, insulation grade, thermal time constant minute.
