EMERSON A6220 工控備件機器人模塊
表1-控制器端子連接器引腳分配引腳信號描述1 0V DC電源2+24V DC電源3接地4未連接未連接5輸入2型號特定描述6輸入1 7輸出2 8輸出1輸入2 PNP NPN PNP NPP D7 LED-電源型號特定擴展PCB D3 LED輸出1 D4 LED輸出2 D6 LED輸入2 D5 LED輸入1 RJ45連接器發射器RJ45連接器接收器D2 LED D1 LED間隙電纜輸出1輸入1輸出2輸入1輸入2 n.c.接地。24 VDC 0 VDC電位計2電位計1可拆卸彈簧加載連接器輸入邏輯跳線S1 J2 J14表2-響應時間詳細信息型號tA（ms）±5%tS（毫秒）±5%45MLA-CTRL-ALG單掃描模式（默認值）4.1 0.13 45MLA-TRL-ALG雙掃描模式（1）（1）可使用這些型號上的DIP開關設置雙掃描模式。4.1 0.25 45MLA-CTRL-BSC單掃描模式（默認值）0.6 0.14 45MLA-TRL-BSC雙掃描模式（1）0.8 0.25 45MLA-CTRL 5.3 0.275 45MLA-CTRL-485 2.1 0.275 45MLA-CTRL-CAN 1.0 0.275表3-跳線設置描述的輸入邏輯跳線連接到PNP輸出（默認值主動“低”（0V）輸入24V 4k3 4k3 PNP NPN羅克韋爾自動化出版物45MLA-IN002C-EN-P-2020年8月3 45MLA控制器安裝說明狀態指示器圖4顯示了控制器主PCB上每個狀態指示器的含義。DIP開關DIP開關設置和說明在本文件中的特定型號章節中詳細介紹。僅在控制器電源關閉時更改DIP開關設置。電位計設置輸出Out1和Out2的時間設置、懸垂持續時間（t_ot）和最小輸出持續時間（t_out）可以使用相應的電位計進行調整，如表5所示。此外，CAN和RS-485控制器模型提供了通過使用串行接口上的指定命令來調整這些設置的靈活性。
Table 1 - Controller Terminal Connector Pin Allocation Pin Signal Description 1 0V DC Power 2 +24V DC Power 3 Ground Ground 4 Not connected Not connected 5 In 2 Model-specific descriptions 6 In 1 7 Out 2 8 Out 1 In 2 PNP NPN PNP NPN D7 LED - Power Model Specific Extension PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45 Connector Emitter RJ45 Connector Receiver D2 LED D1 LED Gaps for cables Out 1 In 1 Out 2 In 1 In 2 n. c. Earth. 24 VDC 0 VDC Pot 2 Pot 1 Removable Spring-Loaded Connector Input Logic Jumpers S1 J2 J14 Table 2 - Response Time Details Model tA (ms) ± 5% tS (ms) ± 5% 45MLA-CTRL-ALG single scan mode (default) 4.1 0.13 45MLA-CTRL-ALG double scan mode (1) (1) Double-scan mode can be set with the DIP switches on these models. 4.1 0.25 45MLA-CTRL-BSC single scan mode (default) 0.6 0.14 45MLA-CTRL-BSC double scan mode (1) 0.8 0.25 45MLA-CTRL 5.3 0.275 45MLA-CTRL-485 2.1 0.275 45MLA-CTRL-CAN 1.0 0.275 Table 3 - Input Logic as Described by Jumper Settings Jumper Connect to PNP Output (Default) Connect to NPN Output In1 Input IN1 active 'high' (+24V) Input IN1 active 'low' (0V) In2 Input IN2 active 'high' (+24V) Input IN2 active 'low' (0V) Input 24V 4k3 4k3 PNP NPN Rockwell Automation Publication 45MLA-IN002C-EN-P - August 2020 3 45MLA Controller Installation Instructions Status Indicators Figure 4 shows the meaning of each status indicator on the main PCB of the controller. DIP Switches DIP switch settings and descriptions are detailed in model-specific sections in this document. Change DIP switch settings only when the controller power is off. Potentiometer Settings The time settings of outputs Out1 and Out2, overhang duration (t_ot) and minimum output duration (t_out), can be adjusted using the corresponding potentiometers, as described in Table 5. Additionally, the CAN and RS-485 controller models offer the flexibility of adjusting these settings through use of specified commands over the serial interface.
