MVME7100-0161工控自動化卡件
使用驅動器菜單和/或驅動器面板工具欄時，您可以一次控制一個驅動器。這意味著，如果您想控制另一個驅動器，則必須釋放當前所控制的驅動器。如果您沒有采取控制措施，則可以清除任何驅動器的故障記錄器。如果您已經控制了驅動器，DriveWindow允許您僅清除受控驅動器的故障記錄器，這樣就不會(huì )對已清除的故障記錄器產生誤解。出于安全原因，在采取控制時，可能導致通信流量過大的命令將被禁用。由于通信量大，驅動器中的看門狗可能會(huì )關閉，從而導致面板丟失。在“文件”菜單的“參數”子菜單中，以下命令在控制驅動器時被禁用（灰色）：?另存為。?在導出子菜單中選擇。?導出子菜單中的所有驅動器。?在驅動變量的上下文菜單中導出。?在“打印”子菜單中選擇。?打印子菜單中的所有驅動器。?在驅動變量的上下文菜單中打印。?比較，除非選擇了打開的參數文件。?下載控制驅動器5-4驅動器窗口2在文件菜單的系統軟件子菜單中，當控制驅動器時，以下命令被禁用（灰色）：?備份。?全部備份。?恢復。?下載另請參閱：控制驅動器獲取控制命令驅動器釋放控制2.1獲取控制筆記！控制驅動器可能會(huì )導致人身傷害或身體損壞。您應該可以物理訪問驅動器，并且必須確保驅動器和機電系統易于控制（例如，您可以看到系統）。遠程控制驅動器可能需要額外的預防措施，因此不建議這樣做。出于安全原因，在采取控制時，可能導致通信流量過大的命令將被禁用。由于通信量大，驅動器中的看門狗可能會(huì )關閉，從而導致面板丟失。如果您當前正在控制另一個驅動器，則必須先釋放它。DriveWindow允許您一次僅控制一個驅動器（除非使用原始控制項）。要控制驅動器，請首先在瀏覽樹窗格中單擊該驅動器來選擇該驅動器。但是，不必選擇其根。選擇其任何分支機構即可。然后，單擊驅動器面板工具欄中的拍攝/釋放控制按鈕，選擇驅動器菜單中的拍攝控制命令，或按Alt+F2。拍攝控制命令也可以在上下文菜單中找到，您可以通過右鍵單擊驅動器來獲得
You can control one drive at a time when using the Drive menu and/or the drive panel toolbar. It means that you have to release currently taken control, if you want to control another drive. If you have no control taken, you are able to clear the fault logger of any drive. If you have taken control of a drive, DriveWindow allows you to clear the fault logger of the controlled drive only, so that there will be no misunderstanding about the fault logger cleared. For safety reasons, commands that may cause heavy communication traffic, are disabled while control is taken. Because of heavy communication traffic, the watchdog in the drive could go off thus causing a panel loss. In the Parameters submenu of the File menu the following commands are disabled (grayed) while control of a drive is taken: ? Save As. ? Selected in the Export submenu. ? All Drives in the Export submenu. ? Export in the context menu of drive variant. ? Selected in the Print submenu. ? All Drives in the Print submenu. ? Print in the context menu of drive variant. ? Compare, unless an open parameter file is selected. ? Download. Controlling Drives 5-4 DriveWindow 2 In the System Software submenu of the File menu the following commands are disabled (grayed) while control of a drive is taken: ? Backup. ? Backup All. ? Restore. ? Download. See Also: Controlling Drives Take Control Commanding a Drive Release Control 2.1 Take Control Note! Controlling a drive may cause personal injury or physical damage. You should have physical access to the drive, and you must be sure that the drive and the electromechanical system are clear to control (you can see the system, for example). Controlling a drive remotely may require extra precautions and is discouraged. For safety reasons, commands that may cause heavy communication traffic, are disabled while control is taken. Because of heavy communication traffic, the watchdog in the drive could go off thus causing a panel loss. If you are currently controlling another drive, you have to release it first. DriveWindow allows you to control just one drive at a time (unless you use the raw control items). To take control of a drive, select first the drive by clicking it in the browse tree pane. It is not necessary to select its root, however. Selection of any of its sub-branches will do. Then either, click the take/release control button in the drive panel toolbar, select the Take Control command in the Drive menu, or press Alt+F2. The Take Control command can also be found in the context menu, which you get by clicking with the right mouse button the drive
