MVME2604-1161B 機械備件
本節中提供了 伺服電機電纜接線信息P輸出和危險電纜的內部連接信息- 命令電纜連接器電線顏色測量針端子#黑色#AT白色#BT屏蔽排液# ET屏蔽排液#N/CTBLK#HT綠色#GT屏蔽排液#1N/CTBLaided屏蔽#N/CT至接地螺柱 機電源電纜電線連接器編號顏色測量針端子 屏蔽/排水管接地黑色 ECPCTxx電機電源電纜電線連接器數字顏色測量針端子 延長電纜長度，用于與ES或DES驅動器連接。 并與單個設備格式解析器一起使用。例如：、：、：和：-CEUxx編碼器反饋電纜電線連接器對顏色表 伺服電機應用指南以下步驟是旨在幫助伺服電機選擇的通用指南。下頁提供的公式應與以下公式結合使用，以確定電機的最終尺寸。如需進一步幫助，請填寫相應的應用數據表頁面，并與當地的AllenBradley銷售辦公室聯系。確定電機速度要求。根據應用絲杠、齒條和銷的動力傳動系配置，傳送或確定伺服電機的平均轉速和峰值。選擇速度曲線，以提供接近您的循環的閉合值。三角形速度曲線/ 確定所需的最小連續電機扭矩。計算電機扭矩，計算公式，或…確定加速負載所需的峰值電機扭矩。如果發動機必須在指定的時間內加速，請使用特定動力傳動系配置的表格確定系統轉速，否則請停止。使用時間來實現每分鐘的峰值，每分鐘的變化?rpm、動力傳動系慣性系統慣性和負載扭矩T以下兩個公式中的一個：系統慣性b-
This section provides servo motor cable wiring information P output and internal connection information of dangerous cables - command cable connector wire color measuring pin terminal # black # AT white # BT shielding drain # ET shielding drain # N/CTBLK # HT green # GT shielding drain # 1N/CTBLaid shield # N/CT to grounding stud machine power cable wire connector number color measuring pin terminal shield/drain pipe grounding black ECPCTxx motor power cable wire connector digital color Color measuring pin terminal extension cable length for connection with ES or DES driver. It is used with a single device format parser. For example:,:,: and: - CEUxx encoder feedback cable wire connector application guide for color table servo motor The following steps are general guidelines designed to help servo motor selection. The formula provided on the next page shall be used in combination with the following formula to determine the final size of the motor. For further assistance, please fill in the corresponding application data sheet page and contact your local Allen Bradley sales office. Determine motor speed requirements. Transmit or determine the average speed and peak value of the servo motor according to the power train configuration of the applied lead screw, rack and pin. Select the velocity curve to provide a closure value close to your loop. Delta speed curve/Determine the minimum continuous motor torque required. Calculate the motor torque, calculate the formula, or... determine the peak motor torque required to accelerate the load. If the engine must accelerate within the specified time, use the table for the specific power train configuration to determine the system speed, otherwise stop. Use time to achieve the peak value per minute, the change per minute ? rpm, the inertia of the power train inertial system and the load torque T, which is one of the following two formulas: system inertia b-
