MVME172-333工業備件
注：為了確保110/230V電源的隔離，輸入電源必須單獨布線，并通過用于輸出接線的單獨配件或壓蓋進入控制單元。從控制單元到墊子的電線可以使用導管埋在地板中，或通過邊緣裝飾件。此類安裝建議使用撓性導管。詳見第6節。確定接線方法，并確定控制單元接線墊的輸入和輸出連接點。5.10最終細節準備安裝布局和電路的工作計劃和圖紙。建議將所有測量和計算記錄并保存在機器的技術文件中。25第6節-安裝和調試開始安裝前，應完整閱讀本手冊。開始工作前，請仔細學習本節內容。安裝和調試應由系統設計師監督。需要一名熟悉工業布線實踐的機械技術人員和一名電工進行安裝。調試應由在安全安裝方面有經驗的訓練有素的電氣技術人員進行。需要以下專用工具：預絕緣對接接頭的壓接工具圖21連接器（如Raychem AD-1522-T）圖22熱收縮用帶反射器附件的熱風槍?zhuān)ㄈ鏡ayhem HL1802E）6.1 MAT INSTALLATION隔離并鎖定機器電源。
檢查地板是否平整、光滑、干凈、無碎屑，以及任何埋地管道或其他布線是否正確到位。拆開墊子，小心保持平整，不要拉扯電線。將墊子放置在地板上的計劃位置，連接線位于檢測區域的外圍。根據圖23將墊段連接在一起。圖23注意：墊線具有黑色外層。兩個具有黑色內護套，兩個具有白色內護套（位置見圖23）?？刂茊卧? 2 3 4 26處的傳感器墊白-黑-白-白-黑，黑-黑-黑，白-白，黑-白，白-黑端子留有足夠的線尾長度，以便在更換墊的情況下重新制作連接，但確?；ミB電線能夠輕松地安裝在邊緣裝飾件下方，而不會(huì )被擠壓。使用下圖24所示的對接連接器連接電線。如果墊線需要延伸，例如前墊到后墊的連接和控制單元連接，則使用額外的一對對接連接器和一段雙導線（參見布線規范-第6.2節）。圖24組合修剪固定安裝中使用的所有活動組合修剪部分必須斜接至45°。這有助于安裝，并有助于保持傳感區域的整體靈敏度。圖24a周邊飾板固定如果控制單元的接線未埋置，則在電線入口和出口位置切割周邊飾板，并切割飾板坡度以適合所選導管系統。
Note: In order to ensure the isolation of 110/230V power supply, the input power supply must be wired separately and enter the control unit through separate fittings or glands for output wiring. The wires from the control unit to the mat can be buried in the floor using conduits or through edge trims. Flexible conduit is recommended for such installations. See Section 6 for details. Determine the wiring method, and determine the input and output connection points of the control unit wiring pad. 5.10 Final details Prepare work plans and drawings for installation layout and circuits. It is recommended that all measurements and calculations be recorded and kept in the technical documentation of the machine. 25 Section 6 - Installation and Commissioning This manual should be read in its entirety before installation begins. Please study this section carefully before starting work. Installation and commissioning shall be supervised by the system designer. A mechanical technician familiar with industrial wiring practice and an electrician are required for installation. The commissioning shall be carried out by trained electrical technicians with experience in safe installation. The following special tools are required: crimping tool for pre insulated butt joint Figure 21 Connector (such as Raychem AD-1522-T) Figure 22 Heat shrinkable hot air gun with reflector accessories (such as Raychem HL1802E) 6.1 MAT INSTALLATION Isolate and lock the machine power supply.
Check that the floor is flat, smooth, clean and free of debris and that any buried piping or other wiring is in place. Remove the mat and be careful to keep it flat. Do not pull the wire. Place the mat at the planned position on the floor, and the connecting line is located at the periphery of the detection area. Connect the cushion sections together according to Figure 23. Fig. 23 Note: The padding line has a black outer layer. Two have black inner sheaths and two have white inner sheaths (see Figure 23 for location). The sensor pad white black white black, black black black, white white, black white, black white, white black terminals at the control unit 1 2 3 4 26 have enough tail length to make a connection again when the pad is replaced, but ensure that the interconnection wire can be easily installed under the edge trim without being squeezed. Use the butt connector shown in Figure 24 below to connect the wires. If the pad wire needs to be extended, such as the connection from the front pad to the rear pad and the control unit connection, use an additional pair of butt connectors and a section of double wires (see Wiring Specifications - Section 6.2). Fig. 24 All the movable combined trim parts used in the combined trim fixing installation must be mitered to 45 °. This facilitates installation and helps maintain the overall sensitivity of the sensing area. Figure 24a Fixing the peripheral trim panel If the wiring of the control unit is not embedded, cut the peripheral trim panel at the wire inlet and outlet, and cut the trim panel slope to fit the selected conduit system.
