MVME167PA-24SE DCS模塊卡件
工廠提供的現場修改驗證驅動器上的電源電纜接地夾是否接觸所有（三個）電纜屏蔽。BR+BR-+-直流電源客戶提供的部件制動繼電器二極管或MOV電弧抑制器MP系列低慣量無刷伺服電機，具有75 mm或更小的框架尺寸9羅克韋爾自動化出版物MP-IN006D-EN-P-2015年1月安裝電機MP系列電機包括一個安裝導桿，用于在機器上對齊電機。優選的緊固件為不銹鋼。安裝必須符合所有當地法規，并使用促進安全和電磁兼容性的設備和安裝實踐。更改連接器方向您可以將連接器外殼旋轉180°。這使您可以將連接器調整到最佳位置，以保護連接免受可能的環境污染，同時提供電纜接入。圓形DIN連接器外殼可沿任一方向旋轉180°。按照以下步驟旋轉DIN連接器。1.在反饋或電源/制動接頭上安裝并完全固定配合電纜。2.用手抓住配合的連接器和電纜插頭，并將其緩慢旋轉至電機外部。3.對另一個接頭重復這些步驟。注意：如果通電，未安裝的電機、斷開的機械聯軸器、松脫的軸鍵和斷開的電纜都是危險的。鎖定并標記拆卸的設備（限制電源）。
向電機通電前，取下軸鍵和其他可能從軸上拋出的機械聯軸器。注意：確保電纜已安裝并受到約束，以防止電纜連接處的不均勻張力或彎曲。當電纜彎曲時，電纜上過大且不均勻的橫向力會(huì )抑制環境密封。注意：連接器設計為在電機安裝期間旋轉到固定位置，并保持在該位置，無需進一步調整。不要多次旋轉連接器，也不要使用工具或過度用力旋轉連接器。過度旋轉或用力會(huì )損壞連接器密封，降低電機的國際防護（IP）等級，如第20頁規范所述。注意：僅對電機連接器和電纜插頭施加力。不要對從電纜插頭伸出的電纜施加力。不要使用工具（例如鉗子和虎鉗）旋轉連接器。10 MP系列75 mm或更小框架尺寸的低慣量無刷伺服電機羅克韋爾自動化出版物MP-IN006D-EN-P-2015年1月安裝電機按照以下步驟安裝電機。1.為電機提供足夠的間隙、散熱質量和氣流，使其保持在0…40°C（32…104°F）的工作溫度范圍內。除非強制冷卻空氣穿過電機，否則不要封閉電機，并使其他發熱設備遠離電機。散熱器要求列于第20頁規范的腳注中。
Factory supplied field modifications verify that the power cable ground clip on the drive contacts all (three) cable shields. BR+BR -+- DC power Customer supplied components Brake relay diode or MOV arc suppressor MP series low inertia brushless servo motor with 75 mm or smaller frame size 9 Rockwell Automation publication MP-IN006D-EN-P-2015 January installation motor MP series motors include a mounting guide for aligning the motor on the machine. The preferred fastener is stainless steel. The installation must comply with all local regulations and use equipment and installation practices that promote safety and electromagnetic compatibility. Changing the connector orientation allows you to rotate the connector housing 180 °. This allows you to adjust the connector to the optimal position to protect the connection from possible environmental pollution while providing cable access. The circular DIN connector housing can be rotated 180 ° in either direction. Follow the steps below to rotate the DIN connector. 1. Install and completely fix the matching cable on the feedback or power/brake connector. 2. Grasp the mating connector and cable plug by hand and slowly rotate them to the outside of the motor. 3. Repeat these steps for the other connector. Note: If the power is on, the unmounted motor, the disconnected mechanical coupling, the loose shaft key and the disconnected cable are dangerous. Lock and mark the removed equipment (restricted power supply).
Before energizing the motor, remove the shaft key and other mechanical couplings that may be thrown from the shaft. NOTE: Make sure that the cable is installed and restrained to prevent uneven tension or bending at the cable connections. When the cable is bent, excessive and uneven lateral forces on the cable will inhibit environmental sealing. Note: The connector is designed to rotate to a fixed position during motor installation and remain in that position without further adjustment. Do not rotate the connector more than once, nor use tools or excessive force to rotate the connector. Excessive rotation or force can damage the connector seal and reduce the international protection (IP) rating of the motor, as described in the specifications on page 20. Note: Apply force to motor connector and cable plug only. Do not apply force to the cable protruding from the cable plug. Do not use tools such as pliers and vises to rotate the connector. 10 MP series low inertia brushless servo motor with 75 mm or smaller frame size Rockwell Automation publication MP-IN006D-EN-P-2015 January installation of motor Install the motor according to the following steps. 1. Provide sufficient clearance, heat dissipation quality and airflow for the motor to keep it within the operating temperature range of 0... 40 ° C (32... 104 ° F). Do not close the motor and keep other heating equipment away from the motor unless forced cooling air passes through the motor. The radiator requirements are listed in the footnote to the specification on page 20.
