MVME162PA-252SE庫存備件
在本手冊中，我們會(huì )在必要時使用注釋?zhuān)蕴嵝涯⒁獍踩马?。標簽也可以在設備上或內部，以提供特定的預防措施。警告：確定在危險環境中可能導致爆炸的做法或情況的信息，這可能導致人身傷害或財產損失或經濟損失。注意：確定可能導致人身傷害財產損失或經濟損失的行為或情況的信息。注意事項有助于您識別危險，避免危險并認識到后果。重要信息確定對成功應用和理解產品至關重要的信息。電擊危險：標簽可能位于設備上或內部，例如驅動器或電機，以提醒人們可能存在危險電壓。燒傷危險：標簽可能位于設備上或內部，例如驅動器或電機，以提醒人們表面可能達到危險溫度。電弧閃光危險：標簽可能位于設備上或內部，例如電機控制中心，以提醒人們潛在的電弧閃光。電弧閃光會(huì )造成嚴重傷害或死亡。穿戴適當的個人防護裝備。遵守安全工作規程和個人防護設備的所有監管要求。羅克韋爾自動化出版年月目錄前言關于本手冊變更摘要。將觸點添加到現有設備續公告油密選擇開關產品數據觸點配置可通過目標表方便地指示。請參閱第頁的表和第頁的表。位置示例：從正面查看操作員位置。位 目標表提供每個給定選擇器開關位置的觸點狀態。如上面示例中所示，當從前面看選擇器開關時，可以看到操作員的位置。每行表示電路的觸點。表示觸點閉合，表示觸點斷開。表中使用了和符號，以幫助選擇組合電路中的正確接觸塊，以滿足功能要求。兩個獨立的因素決定了觸點在給定位置是打開還是關閉。
In this manual, we will use notes when necessary to remind you of safety precautions. Labels can also be on or inside the equipment to provide specific precautions. WARNING: Information identifying practices or situations that could lead to an explosion in a hazardous environment, which could result in personal injury or property damage or economic loss. Note: Information identifying actions or circumstances that may result in personal injury, property damage or economic loss. Precautions can help you identify hazards, avoid hazards and recognize consequences. Important information identifies information that is critical to the successful application and understanding of the product. Electric shock hazard: The label may be located on or inside the equipment, such as the driver or motor, to remind people that dangerous voltage may exist. Burn hazard: Labels may be located on or inside equipment, such as drives or motors, to warn people that the surface may reach dangerous temperatures. Arc flash hazard: The label may be located on or inside the equipment, such as motor control center, to remind people of potential arc flash. Arc flash can cause serious injury or death. Wear appropriate personal protective equipment. Comply with all regulatory requirements for safe work practices and personal protective equipment. Rockwell Automation publishes a summary of changes to this manual in the foreword of the monthly catalog. Adding contacts to existing equipment Continued bulletin Oil tight selector switch Product data Contact configuration can be easily indicated through the target table. See Table on page and Table on page. Example location: View the operator's position from the front. The bit target table provides the contact status for each given selector switch position. As shown in the example above, when looking at the selector switch from the front, you can see the position of the operator. Each line represents the contact of the circuit. Indicates that the contact is closed, indicating that the contact is open. The and symbols are used in the table to help select the correct contact block in the combined circuit to meet the functional requirements. Two independent factors determine whether the contact is open or closed at a given position.
