MVME162PA-242LE模擬量輸入模塊
端子是安全的。照明。鏈接到位或重置按鈕功能正常。裝置似乎工作保險絲熔斷。輸出保險絲。正確，但沒有損壞或不正確的接線。所有接線是否損壞。輸出上的故障導致任何內部繼電器移動。故障安全輸出 。如果外部連接不正確，機器不會(huì )停止所有到接觸器的接線都有錯誤。輪廓已按下。運行“綠色”熄滅。如果按下“不允許使用機器配置文件”，機器不會(huì )停止。更換控制器。運行“綠色”保持亮起。維護在嘗試任何維護工作之前，應完整閱讀本節內容。請注意歐盟指令作為年工作設備的提供和使用條例在英國實施下的計劃預防性維護條例。在維護操作期間，在使用系統之前，斷開機器的原動機。遵守電氣安全預防措施。 當使用帶密封的封閉蓋時，必須將型材底部切回的長度。必須小心切割，以確保型材底部完全修剪，不會(huì )留下齊平表面。陰影區域必須用砂紙打磨粗糙封口蓋用個密封圈模制，每個密封圈帶有一個橡膠塞。安裝電阻器時，保持插頭完好無損。在進行電纜連接時，選擇所需的電纜出口，并用打孔器從索環上取下插頭。將連接電纜穿過孔。 用其中一根針刺破每根銅線。按所示方向向外楔入將接頭的針觸點直接壓入銅線。小心連接器的窄側楔形必須向外突出。折回蓋的密封唇 如圖所示，在封口蓋的陰影區域涂上粘合劑，然后粘貼到型材邊緣，加壓秒以確保粘合。 在陰影區域的其余部分涂上粘合劑，使密封唇與型材接觸。重要事項：將粘合劑均勻涂抹在陰影區域！不要讓粘合劑進入型材內部。應用 +棕白色
The terminal is safe. Lighting. Link in place or reset button functions normally. The unit appears to be working with a blown fuse. Output fuse. Correct, but no damaged or incorrect wiring. Whether all wiring is damaged. A fault on the output causes any internal relays to move. Fail safe output. If the external connection is incorrect, the machine will not stop all the wiring to the contactor has errors. Contour pressed. Running "green" turns off. If you press "Do not allow to use machine configuration file", the machine will not stop. Replace the controller. Running "green" remains lit. Maintenance Read this section completely before attempting any maintenance work. Please note the planned preventive maintenance regulations under the EU Directive as an annual provision and use of working equipment in the UK. During maintenance operations, disconnect the prime mover of the machine before using the system. Observe electrical safety precautions. When using a closed cover with a seal, the bottom of the profile must be cut back to the length. Care must be taken in cutting to ensure that the bottom of the profile is completely trimmed without leaving a flush surface. The shadowed area must be sanded rough. The closure cap is molded with sealing rings, each with a rubber plug. Keep the plug intact when installing the resistor. When connecting cables, select the required cable outlet and use a hole punch to remove the plug from the grommet. Pass the connecting cable through the hole. Pierce each copper wire with one of the needles. Press the pin contact of the connector directly into the copper wire by wedging outward in the direction shown. Be careful that the narrow side wedge of the connector must protrude outward. The sealing lip of the fold back cover is as shown in the figure. Apply adhesive to the shaded area of the cover, and then stick it to the edge of the profile. Press for seconds to ensure adhesion. Apply adhesive to the rest of the shaded area so that the sealing lip contacts the profile. IMPORTANT: Apply the adhesive evenly to the shaded area! Do not allow the adhesive to enter the inside of the profile. Application+brown white
