MVME162P-344SE工控備件機器人模塊
燒傷危險：標簽可能位于設備上或內部，例如驅動器或電機，以提醒人們表面可能達到危險溫度。致動距離：響應距離：最大速度：控制單元通電后，還必須按下該按鈕。與控制單元的外形連接這些端子用于將外形連接到：=棕色內部導體。=白色外部連接器。參見應用。注：配置文件必須以結尾?串聯電阻黃色。當兩個外形直接連接到和并聯時，每個外形應使用電阻器藍色終止。并聯和串聯連接可選連接方法并聯連接最多可以并聯兩個型材，以幫助在某些應用中輕松布線。使用電阻器藍色串聯連接如果要使用多個配置文件，它們通常如圖所示串聯連接。使用電阻器黃色電氣連接安全控制單元表面安裝導軌安裝+電源保險絲停止紅色打開黃色運行綠色電源保險絲安全保險絲+停止紅色打開黃色指示燈運行綠色控制單元安裝和布線按照步驟至正確安裝重要事項：布線必須符合國家電氣規范和適用的地方法規和條例電源選擇開關如果使用或電源，則應在打開電源前適當設置電壓選擇開關。該裝置在制造時設置為。電源輸入端子如果使用或電源，則應將其與保護接地接地一起連接至所示端子。
保護接地線的尺寸應至少等于電源線的尺寸。同時檢查如果使用這些端子，則忽略輸入端子+和如果使用電源，則應將電源連接到這些端子，以確保觀察到正確的極性。不要與的端子進行任何連接。如果使用或電源，則必須根據國際電氣安全規程將其與主電源隔離。一個極應接地。對于，負極應接地接地。對于，電源的接地接地極應連接到端子。輔助輸出端子和該端子提供了一個輔助常閉觸點即，當綠色“運行”燈熄滅時閉合，適用于指示或報警裝置。由于這是一個輔助設備，因此不得將其連接到安全電路。安全輸出端子和這些是用于連接到機器安全電路的無電壓觸點，即它們與機器接觸器控制電路串聯連接。時的最大額定值。這兩個安全電路都有內部保險絲，但也必須使用快速熔斷器進行外部保護。如果使用一個接觸器，則需要端子和，端子和應跨接在一起。對于具有個獨立控制電路即雙通道系統的個接觸器，一個接觸器使用，另一個接觸器采用。
Burn hazard: Labels may be located on or inside equipment, such as drives or motors, to warn people that the surface may reach dangerous temperatures. Actuation distance: response distance: maximum speed: the button must be pressed after the control unit is powered on. Connection to the profile of the control unit These terminals are used to connect the profile to the:=brown internal conductor= White external connector. See Application. Note: The configuration file must end in ? series resistance yellow. When two profiles are connected directly to and in parallel, each profile shall be terminated in blue with a resistor. Parallel connection and series connection Optional connection methods Parallel connection can be used to connect up to two profiles in parallel to facilitate easy wiring in some applications. Use resistor blue series connection If you want to use multiple configuration files, they are usually connected in series as shown in the figure. Use resistor yellow for electrical connection Safety control unit Surface mounting rail installation+power fuse stop red for operation Green power fuse safety fuse+stop red for operation Yellow indicator light for operation Green control unit installation and wiring Follow steps to correct installation Important: Wiring must comply with national electrical specifications and applicable local regulations and rules Power selection switch if used or power supply, The voltage selector switch shall be set properly before turning on the power supply. The device is set to at the time of manufacture. If the or power supply is used, the power input terminal shall be connected to the terminal shown together with the protective grounding.
The size of the protective earth wire shall be at least equal to the size of the power line. Also check that if these terminals are used, the input terminals+are ignored and if a power supply is used, the power supply should be connected to these terminals to ensure that the correct polarity is observed. Do not make any connections to the terminals of. If the or power supply is used, it must be isolated from the main power supply according to the international electrical safety regulations. One pole should be grounded. For, the negative pole should be grounded. For, the grounding electrode of the power supply shall be connected to the terminal. The auxiliary output terminal and the terminal provide an auxiliary normally closed contact, that is, it is closed when the green "running" light is off, and it is applicable to the indication or alarm device. Since this is an auxiliary device, it must not be connected to a safety circuit. The safety output terminals and these are voltage free contacts used to connect to the machine safety circuit, that is, they are connected in series with the machine contactor control circuit. Maximum rating at. Both safety circuits have internal fuses, but they must also be externally protected with quick fuses. If a contactor is used, terminals and shall be connected together. For each contactor with independent control circuit, i.e. dual channel system, one contactor is used and the other contactor is used.
