MVME162P-344E工控備件機器人模塊
安裝后，本手冊涵蓋了系統所有部件的安裝和使用，包括特殊形狀和尺寸的傳感器墊。所有安裝程序應由經過適當培訓的合格人員執行，并應符合法定安全要求。安裝前請完整閱讀本手冊。安裝后，應將本手冊保存在安全且可接近的地方。如需進一步幫助，請聯系供應商。第節儲存和搬運儲存控制裝置和墊傳感器應儲存在至+的溫度范圍內。墊子傳感器應垂直存放。搬運和運輸控制裝置和墊傳感器應在至+的溫度范圍內運輸。如有必要，原始包裝或類似包裝應與加固一起使用，以防止損壞和彎曲。始終小心打開包裝，避免被刀具等損壞。當傳感器墊移動到位時，切勿通過其連接線拉動或提起傳感器。對于較大的傳感器墊，需要兩個人來安全提升，并防止過度彎曲損壞傳感器墊的風險。第節系統描述系統包括一個或多個互連的壓敏墊和一個控制單元。檢測區域內沒有“死區”。單個傳感器墊部分有矩形標準尺寸，也有特殊切割形狀，最大尺寸為最大標準墊。所有傳感器墊具有相同的結構和操作原理。每個墊子都有兩塊導電板由不導電的可壓縮隔板隔開。這些墊子在下工作，并串聯在一起，以形成機器周?chē)ｋU區域的地面感應系統。通過墊子的電路由控制單元監控，當區域空閑時，控制單元向機器控制電路提供信注意確定可能導致人身傷害財產損失或經濟損失的行為或情況的信息。注意事項有助于您識別危險，避免危險并認識到后果。重要信息確定對成功應用和理解產品至關重要的信息。電擊危險標簽可能位于設備上或設備內部，例如驅動器或電機，以提醒人們可能存在電壓。對于個接觸器，請參見壓敏安全墊系統安裝和用戶手冊安裝前請閱讀本手冊。當任何墊被踩下時，導電板接觸，電路中的電阻下降。這由關閉機器的控制單元監控。將檢測到主接線或控制單元中的任何單個電氣故障，并且控制單元輸出將進入安全狀態。模制乙烯基傳感器墊密封至控制單元。該單元包括一個八通道傳感墊系統。當踩下任何墊子時，控制單元將關閉機器，并在信道故障狀態顯示屏上顯示正在操作的墊子。有兩種操作模式手動復位和自動復位。號。
After installation, this manual covers the installation and use of all components of the system, including sensor pads with special shapes and sizes. All installation procedures shall be carried out by suitably trained and qualified personnel and shall comply with statutory safety requirements. Please read this manual completely before installation. After installation, keep this manual in a safe and accessible place. For further assistance, please contact the supplier. Section Storage and Handling Storage controls and pad sensors should be stored within a temperature range of+. Cushion sensors should be stored vertically. The handling and transport controls and pad sensors shall be transported within a temperature range of to+. If necessary, the original or similar packaging shall be used with reinforcement to prevent damage and bending. Always open the package carefully to avoid being damaged by knives, etc. When the sensor pad moves in place, do not pull or lift the sensor through its connecting wire. For larger sensor pads, two people are required to safely lift and prevent the risk of damaging the sensor pads by excessive bending. Section System Description The system consists of one or more interconnected pressure sensitive pads and a control unit. There is no "dead zone" in the detection area. The single sensor pad has rectangular standard size and special cutting shape. The maximum size is the maximum standard pad. All sensor pads have the same structure and operating principle. Each cushion has two conductive plates separated by non-conductive compressible partitions. These pads work under and in series to form a ground sensing system in the hazardous area around the machine. The circuit through the mat is monitored by the control unit. When the area is free, the control unit provides information to the machine control circuit to determine the behavior or situation that may cause personal injury, property loss or economic loss. Precautions can help you identify hazards, avoid hazards and recognize consequences. Important information identifies information that is critical to the successful application and understanding of the product. Shock hazard labels may be located on or inside the equipment, such as drives or motors, to alert people that voltage may be present. For each contactor, please refer to the installation of pressure-sensitive safety pad system and the user manual. Please read this manual before installation. When any pad is stepped down, the conductive plate contacts and the resistance in the circuit decreases. This is monitored by the control unit that shuts down the machine. Any single electrical fault in the main wiring or control unit will be detected, and the control unit output will enter the safe state. Molded vinyl sensor pads are sealed to the control unit. The unit includes an eight channel sensing pad system. When any mat is depressed, the control unit shuts down the machine and displays the mat in operation on the channel fault status display. There are two operation modes: manual reset and automatic reset. number.
