MVME162-433，DCS工控模塊備件
每次按下按鈕時，觸摸圖標都會(huì )打開。我們建議使用食指激活觸摸按鈕。在計量模式下，按鈕和如圖所示用于顯示所顯示測量值的最大值和需求值平均值。圖前面板顯示項目描述活動警報狀態指示燈。實際能耗率狀態指示器。閃爍速度越快表示消耗率越高。根據退出按鈕，最大頻率為快速按下退出子菜單或退出編程模式下的編程菜單。在編程過程中，按住退出至少秒以退出編程菜單。按確認并返回計量顯示，然后退出編程菜單，而不保存更改。要保存更改，請使用向上和向下箭頭轉到結束菜單，然后按程序選擇。不在編程中時，按住秒以上可查看信息頁面。在計量模式下，快速按下可滾動查看能量計數器。向上按鈕按向上按鈕瀏覽菜單并增加要設置的值。向下按鈕按下向下按鈕瀏覽菜單并減少要設置的值。程序選擇按鈕按住程序選擇按鈕至少秒以訪問編程菜單。在編程過程中，按下編程選擇確認激活頁面中的編程值。按程序選擇進入和退出活動頁面上的編輯模式。如果不在編程中，則按程序選擇選擇要顯示的測量值?？焖侔聪驴稍谟嬃匡@示頁面中滾動。測量屏幕列表見表和表。年月第章單元概述附加按鈕功能某些按鈕有兩種功能。要訪問第二個功能，請按住按鈕秒鐘以上。顯示信息屏幕，提供參考標準固件版本和制造年份。重置顯示變量的最大值。您必須按確認重置。重置顯示變量的需求。您必須按確認重置。年月單元概述第章顯示功能圖功能顯示圖標報警圖標指示高值報警指示低值報警顯示項描述相移指示器電感或電容。該標志基于實際潮流的方向。正消耗功率，負發電功率。有關更多信息，請參見附錄中功率和功率因數的幾何表示。在編程模式下，當可以編輯參數時，指示器顯示。表示測量值相位線到中性點或線到線。表示測量值相位線到中性點或線到線。表示測量值相位線到中性點或線到線。工程單位和乘數指示器，。報警顯示功能激活。編程功能激活。為能量計數器留出的區域見表文本消息日期和時間格式:。表示計量值為需求或最大值。顯示項目說明表示顯示的計量值為系統三相值。表示電壓旋轉的相序錯誤報警。配置鎖定開關未激活。始終表示已解鎖。串行數據傳輸和接收的指示。年月第章裝置概述選擇要顯示的數據表和表提供了導航前面板顯示器上可用的計量數據顯示的指南。
Each time the button is pressed, the touch icon opens. We recommend using the index finger to activate the touch button. In metering mode, the buttons and, as shown in the figure, are used to display the maximum value of the displayed measured value and the average value of the demand value. Figure The front panel shows the item description active alarm status indicator. Actual energy consumption rate status indicator. The faster the flashing speed is, the higher the consumption rate is. According to the exit button, the maximum frequency is to quickly press to exit the submenu or exit the programming menu in the programming mode. During programming, press and hold Exit for at least seconds to exit the programming menu. Press OK and return to the metering display, then exit the programming menu without saving the changes. To save your changes, use the up and down arrows to go to the end menu and press Program Select. When not in programming, press and hold for more than seconds to view the information page. In metering mode, press briefly to scroll through the energy counters. Up ButtonPress the up button to navigate through the menu and increase the value to be set. Down ButtonPress the down button to navigate through the menu and decrease the value to set. Program selection button Press and hold the program selection button for at least seconds to access the programming menu. During programming, press Programming Select to confirm the programmed value in the active page. Press Program Select to enter and exit edit mode on the active page. If it is not in programming, select the measurement value to be displayed according to the program selection. Press briefly to scroll through the metering display page. The list of measurement screens is shown in Table and Table. Year Month Chapter Unit Overview Additional Button Functions Some buttons have two functions. To access the second function, press and hold the button for more than seconds. The information screen is displayed, providing the reference standard firmware version and year of manufacture. Reset the maximum value of the display variable. You must press OK to reset. Reset the demand for display variables. You must press OK to reset. Year Month Unit Overview Chapter Display Function Chart Function Display Icon Alarm Icon Indication High Value Alarm Indication Low Value Alarm Display Item Description Phase Shift Indicator Inductance or Capacitance. This sign is based on the direction of the actual current. Positive power consumption, negative power generation. For more information, see the geometric representation of power and power factor in the appendix. In programming mode, the indicator displays when the parameter can be edited. Indicates the measured value phase line to neutral or line to line. Indicates the measured value phase line to neutral or line to line. Indicates the measured value phase line to neutral or line to line. Engineering Units and Multiplier Indicators,. The alarm display function is activated. The programming function is active. The area reserved for the energy counter is shown in the table Text Message Date and Time Format:. Indicates that the measured value is demand or maximum value. The displayed item description indicates that the displayed metering value is the three-phase value of the system. Indicates the phase sequence error alarm of voltage rotation. The configuration lockout switch is not active. Always indicates unlocked. Indication of serial data transmission and reception. Year Month Chapter Device Overview Selecting the data tables and tables to display provides guidelines for displaying the metering data available on the navigation front panel display.
