MVME162-12備件模塊
檢查機械安裝檢查傳感器墊周邊裝飾件和聯合裝飾件是否完好無損，是否正確定位和固定。檢查是否達到了設計的安全距離。檢查除了通過墊子之外，是否無法進入危險區域，并且任何固定防護裝置等是否根據設計進行了定位，并且是否安全。檢查危險區和墊子系統之間是否有人。檢查當前或可預見的環境條件是否符合設計階段考慮的環境條件。檢查安裝是否無設計階段未預見到的危險。檢查所有警告通知是否到位。檢查是否已安裝所需的任何其他保護措施。檢查電氣功能確保墊子上沒有人員和設備。暫時斷開機器控制系統提供的任何自動復位功能?；謴蜋C器電源，但確保機器原動機仍與機器最終接觸器斷開。僅手動模式使用控制單元時不相關檢查控制單元綠色電源亮起綠色手動復位亮起復位按鈕中的復位燈亮起紅色機器啟用關閉。。按下并松開重置按鈕檢查機器啟用是否亮起，重置燈是否熄滅站在墊子上，檢查機器啟用的是否熄滅。離開機器，檢查機器已啟用是否熄滅，重置按鈕是否點亮。按下并松開重置按鈕，檢查機器啟用是否亮起，重置按鈕是否熄滅。重復上述測試，檢查遠程重置按鈕和指示燈如果安裝。重復上述步驟，檢查連接到墊子系統的任何狀態監測的正確操作。僅限自動重置模式使用控制單元時不相關檢查控制單元上的綠色電源亮起綠色機器已啟用。站在墊子上，檢查機器已啟用是否熄滅。離開機器，檢查機器啟用是否亮起。。重復上述步驟，以檢查連接到墊系統的任何狀態監測的正確操作?？刂茊卧δ軆H自動重置模式。檢查控制單元綠色電源亮起綠色機器啟用亮起通道故障至亮起綠色，與安裝的墊子數量相匹配。站在號墊子上，檢查機器啟用熄滅，信道故障變?yōu)榧t色。離開墊子，檢查控制系統是否恢復到與上述第項相同的狀態。對連接到控制單元的每個墊重復此過程，檢查相應的通道故障是否變?yōu)榧t色。僅手動重置模式。檢查控制單元綠色電源亮起綠色機器啟用亮起通道故障至亮起綠色，與安裝的墊數量相匹配。站在號墊子上，檢查機器啟用熄滅，通道故障變?yōu)榧t色。通過操作重置按鈕關閉機器，手動重置系統，然后檢查控制系統返回到與上述項目相同的狀態。
Check the mechanical installation. Check whether the trim around the sensor pad and the joint trim are intact and correctly positioned and fixed. Check whether the designed safety distance is reached. Check whether it is impossible to enter the dangerous area except through the mat, and whether any fixed protective devices are positioned according to the design and safe. Check for people between the hazardous area and the mat subsystem. Check whether the current or foreseeable environmental conditions meet the environmental conditions considered at the design stage. Check whether the installation is free from dangers not foreseen at the design stage. Check that all warning notices are in place. Check that any other protective measures required have been installed. Check the electrical function to ensure that there are no people and equipment on the mat. Temporarily disconnect any automatic reset functions provided by the machine control system. Restore the machine power, but ensure that the machine prime mover is still disconnected from the final contactor of the machine. The manual mode only is irrelevant when using the control unit. Check the control unit. The green power is on. The green manual reset is on. The reset lamp in the reset button is on. The red machine is on. The machine is off.. Press and release the reset button to check whether the machine enabled is on, whether the reset lamp is off, stand on the mat and check whether the machine enabled is off. Leave the machine and check whether the machine is enabled and turned off, and whether the reset button is on. Press and release the reset button, and check whether the machine enabling is on and the reset button is off. Repeat the above test and check if the remote reset button and indicator are installed. Repeat the above steps to check the correct operation of any condition monitoring connected to the mat subsystem. Automatic reset mode only Not relevant when using the control unit Check that the green power on the control unit lights up Green machine is enabled. Stand on the mat and check that the machine is enabled and turned off. Leave the machine and check that the machine activation is lit.. Repeat the above steps in order to check the correct operation of any condition monitoring connected to the cushion system. The control unit function only automatically resets the mode. Check that the green power of the control unit lights up green The machine enable lights up the channel fault to light up green, matching the number of mats installed. Stand on the number mat and check that the machine is enabled and off, and the channel fault turns red. Leave the mat and check whether the control system is restored to the same state as item above. Repeat this process for each pad connected to the control unit and check whether the corresponding channel fault turns red. Manual reset mode only. Check that the green power of the control unit lights up green Machine enable lights up Channel fault lights up green, matching the number of pads installed. Stand on the No. mat and check that the machine is enabled and off, and the channel fault turns red. Shut down the machine by operating the reset button, reset the system manually, and then check that the control system returns to the same state as the above items.
