MVME162-040機械備件
這樣做或使用未經批準的零件或修改可能導致墊子系統無法達到其規定性能。服務如需服務和協助，請聯系供應商。尺寸型號。周邊裝飾指定長度兩件式周邊裝飾指定長度帶電纜干線單元裝飾指定長度保護電線導管指定長度控制單元 毫米英寸目錄號。目錄編號每周建議的常規檢查和測試記錄見第節。全面檢查和測試記錄見第節建議每月次。日期檢查人注釋日期檢查人員注釋圖紙編號更改編號安裝說明系列或更小框架尺寸的低慣量無刷伺服電機，目錄號，主題頁重要用戶信息目錄號說明關于系列低慣量電機開始之前安裝電機產品尺寸電機負載力額定值連接器數據拆卸和安裝軸鍵電機電纜和附件套件規格附加資源系列或較小框架尺寸自動化年月重要用戶信息在安裝配置操作或維護本產品之前，請閱讀本文檔以及有關本設備安裝配置和操作的附加資源部分中列出的文檔。除所有適用的法規和標準的要求外，用戶還需要熟悉安裝和接線說明。包括安裝調整投入使用組裝拆卸和維護在內的活動需要由經過適當培訓的人員按照適用的實踐規范進行。如果以制造商未規定的方式使用本設備，則設備提供的保護可能會(huì )受損。在任何情況下，自動化股份有限公司均不對因使用或應用本設備而導致的間接或后果性損害負責。本手冊中的示例和圖表僅用于說明目的。由于與任何特定安裝相關的許多變量和要求，自動化股份有限公司無法根據示例和圖表承擔實際使用的責任。
Doing so or using unapproved parts or modifications may cause the mat subsystem to fail to achieve its specified performance. Service For service and assistance, please contact the supplier. Size and model. Perimeter decoration Specified length Two piece peripheral decoration Specified length Cable trunk unit decoration Specified length Protection wire conduit Specified length Control unit millimeters inches Catalog number. The recommended weekly routine inspection and test records for catalog number are given in section. See the recommended monthly times in section for comprehensive inspection and test records. Date Checker's Note Date Checker's Note Drawing Number Change Number Installation Instructions Series or smaller frame size low inertia brushless servo motor, catalog number, Important user information on the topic page Catalog number description About installing the motor before the start of a series of low inertia motors Product size Motor load force rating Connector data Removing and installing the shaft key Motor cable and accessory kit specifications Additional resources Series or smaller frame size Automation important user information Before installing, configuring, operating or maintaining this product, Please read this document and the documents listed in the Additional Resources section about the installation configuration and operation of this device. In addition to the requirements of all applicable codes and standards, users need to be familiar with the installation and wiring instructions. Activities including installation, adjustment, putting into use, assembly, disassembly and maintenance shall be carried out by appropriately trained personnel in accordance with applicable codes of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be damaged. In no case shall Automation Co., Ltd. be liable for indirect or consequential damages caused by the use or application of this equipment. The examples and diagrams in this manual are for illustrative purposes only. Due to the many variables and requirements associated with any particular installation, Automation GmbH cannot assume responsibility for actual use based on examples and diagrams.
