MVME162-012A自動化模塊備件
NEMA 3、4X、6、12、13振動10-55Hz，1個振幅，符合或超過IEC 60947--5-2沖擊30g，1ms脈沖持續時間，符合或超出IEC 60947-5--2工作溫度-40_C至+56_C（-40_F至+150_F）相對濕度最大95%UL認證，CSA認證，和CE標記的所有適用指令Dimension Fiber Optic 99.1（3.9）57.2（2.25）24.9（1.05）2校準反光/偏振反光通過順時針轉動靈敏度電位計將靈敏度調整至最大設置。將傳感器對準反射器，直到傳感器上的對準指示燈打開（亮操作）或關閉（暗操作）。為了確保光束為中心，在水平面上掃描反射器上的光束，并確定對準指示器打開和關閉的位置。將光束設置在兩個位置之間的中間位置。在垂直平面上執行相同操作。用要檢測的物體斷開光束，檢查對準指示器是否關閉?？赡苄枰岣哽`敏度或更換較小尺寸的反射器，以檢測小的半透明或透明物體。通過移除對象恢復光束，并檢查對齊指示器是否再次打開。對于有光澤的物體，調整傳感器角度，使光束不垂直于物體。對于高反射材料，使用偏振回射傳感器。通過順時針轉動靈敏度電位計，將靈敏度調整至最大設置。將接收器對準光源，直到接收器上的對準指示燈打開（亮操作）或關閉（暗操作）。為了確保光束是百分之一，在水平面上掃過接收器，并確定對準指示器打開和關閉的位置。將光束設置在兩個位置之間的中間位置。在垂直平面上執行相同操作。對于透明或半透明材料，可能需要將靈敏度降低到較低的設置，或者檢測小于有效光束的物體。漫射模式（包括標準、擴展范圍、廣角和固定焦點）通過順時針轉動靈敏度電位計將靈敏度調整到最大設置。將傳感器對準要檢測的物體，直到控制裝置上的對準指示器打開（亮操作）或關閉（暗操作）。為了確保光束是百分之一，在水平面上掃描對象上的光束，并確定對齊指示器打開和關閉的位置。
NEMA 3, 4X, 6, 12, 13 Vibration 10--55Hz, 1 amplitude, meets or exceeds IEC 60947--5--2 Shock 30g with 1ms pulse duration, meets or exceeds IEC 60947--5--2 Operating Temperature --40_C to +56_C (--40_F to +150_F) Relative Humidity 95% max Approvals UL listed, CSA approved, and CE marked for all applicable directives DimensionFiber Optic 99.1 (3.9) 57.2 (2.25) 24.9 (1.05) 2 Alignment Retroreflective/Polarized Retroreflective Adjust the sensitivity to the maximum setting, by turning the sensitivity potentiometer clockwise. Aim the sensor on the reflector until the alignment indicator on the sensor turns On (light operate) or Off (dark operate). To be certain that the beam is cente, sweep the beam on the reflector in the horizontal plane and determine the position the alignment indicator turns On and then Off. Set the beam halfway between both positions. Do the same in the vertical plane. Break the beam with the object to be detected and check to see if the alignment indicator turns Off. It may be necessary to uce the sensitivity or change to a smaller sized reflector to detect small, translucent or transparent objects. Restore the beam by removing the object and check to see if the alignment indicator turns On again. For shiny objects angle the sensor so that the beam is not perpendicular to the object. For highly reflective materials use a polarized retroreflective sensor. Transmitted Beam Adjust the sensitivity to the maximum setting, by turning the sensitivity potentiometer clockwise. Aim the receiver at the light source until the alignment indicator on the receiver turns On (light operate) or Off (dark operate). To be certain the beam is cente, sweep the beam ross the receiver in the horizontal plane and determine the position the alignment indicator turns On and then Off. Set the beam halfway between both positions. Do the same in the vertical plane. It may be necessary to uce the sensitivity to a lower setting for transparent or translucent materials or to detect objects smaller than the effective beam. Diffuse Modes (Including standard, extended range, wide angle and fixed focus) Adjust the sensitivity to the maximum setting by turning the sensitivity potentiometer clockwise. Aim the sensor at the object to be detected until the alignment indicator on the control turns On (light operate) or Off (dark operate). To be certain that the beam is cente, sweep the beam on the object in the horizontal plane and determine the position the alignment indicator turns On and then Off.
