MVME162-011A機器人備件
目錄首選可用性目錄。編號為粗體。出版物A117-CA001A-EN-P公告電機保護斷路器公告電機保護電路斷路器為單個電機負載提供短路和過載保護。預裝的內部處理器便于安裝和布線。一般信息目錄產品選擇電機保護電流范圍0.1630 A UL列出的電機負載? 短路保護? 過載保護可見跳閘指示高電流限制高開關容量認證標準符合電機保護斷路器可提供以下保護和控制功能。斷開電機分支電路分支電路、短路保護（磁保護）過載保護（熱保護）開關（手動）在北美，電氣規范要求單個電機分支電路由UL/CSA認證的保險絲、斷路器或自保護雙聯電機控制器保護。D和F機架：D和F框架電機保護斷路器可能有2個cULus列表——作為手動、自保護雙聯電機控制器和手動電機控制器（具有電機斷開和組安裝的可選批準）。當UL/CSA列為手動、自保護雙電機控制器時，電機保護斷路器提供了保護和控制單個電機分支電路的所有必要的NEC/CEC要求，無需額外的保護裝置。在某些較高的電壓和電流（尤其是600V）下，一些D和F框架設備僅被UL/CSA列為手動電機控制器（具有電機斷開和組安裝的可選批準）。在NEC/CEC集團安裝中，必須按照要求使用上游分支電路、短路保護裝置（BCPD）的適當規則應用這些裝置。電機保護斷路器的具體額定值見第2-18頁的表?？蚣埽嚎蚣茈姍C保護斷路器經UL認證/CSA認證為手動電機控制器（具有電機斷開和組安裝的可選批準）。在NEC/CEC集團安裝中，必須按照要求使用上游分支電路、短路保護裝置（BCPD）的適當規則應用這些裝置。電機保護斷路器的具體額定值見第2-18頁的表-一、 J和L框架：如第2-9頁表格所示，-I、J和L型框架電機保護斷路器被列為斷路器。在這些情況下，電機保護斷路斷路器提供了保護和控制單個電機分支電路的所有必要的NEC/CEC要求，無需額外的保護裝置。
catalogs Prefer availability cat. nos. are bold. Publication A117-CA001A-EN-P Bulletin Motor Protection Circuit Breakers The Bulletin Motor Protection Circuit Breakers provide short circuit and overload protection for individual motor loads. Ftoryinstalled internal cessories make installation and wiring easy. General Information Table of Contents Product Selection Motor Protection Current Range 0.1630 A UL Listed for Motor Loads ? Short Circuit Protection ? Overload Protection Visible Trip Indication High Current Limiting High Switching Capity Certifications Standards pliance Motor Protection Circuit Breakers may provide the following protective and control functions. Disconnect for Motor Branch Circuit Branch-Circuit, Short-Circuit Protection (Magnetic Protection) Overload Protection (Thermal Protection) Switching (Manual) In North America, electrical codes require that an individual Motor Branch Circuit be protected by a UL/CSA Listed Fuse, Circuit Breaker or Self-Protected bination Motor Controller. D and F Frames: The D and F frame Motor Protection Circuit Breakers may have 2 cULus Listings – as Manual, Self-Protected bination Motor Controllers and as Manual Motor Controllers (with optional approvals for Motor Disconnect and Group Installation). When UL/CSA listed as Manual, Self-Protected bination Motor Controllers, the Motor Protection Circuit Breakers provide all of the necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices. At some higher voltages and currents (particularly at 600V), a few of the D and F frame devices are only UL/CSA Listed as Manual Motor Controllers (with optional approvals for Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must be applied per the appropriate rules which require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the table on page 2-18 for the specific ratings of eh Motor Protection Circuit Breaker. Frame: The frame Motor Protection Circuit Breakers are UL Listed/CSA Certified as Manual Motor Controllers (with optional approvals for Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must be applied per the appropriate rules which require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the table on page 2-18 for the specific ratings of eh Motor Protection Circuit Breaker. -I, J and L Frames: The -I, J and L frame Motor Protection Circuit Breakers are cULus Listed as Circuit Breakers as shown in the table on page 2-9. In these cases, the Motor Protection Circuit Breakers provide all of the necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.
