EMERSON KJ4002X1-BB1控制主板卡件
定時器2 IRQ清除（T2IC）定時器2 IRQ-清除（T2IC）寄存器用于清除定時器2引起的中斷。寫入此寄存器（位于BAR2中地址的偏移量0x34處）會(huì )導致定時器2的中斷被清除。這也可以通過將“0”寫入定時器控制狀態寄存器（CSR1）的相應“定時器x引起的IRQ”字段來完成。該寄存器是只讀的，寫入的數據是無關的。定時器3 IRQ清除（T3IC）定時器3 IRQ-清除（T3IC）寄存器用于清除定時器3引起的中斷。寫入此寄存器（位于BAR2中地址的偏移量0x38處）會(huì )導致計時器3的中斷被清除。這也可以通過將“0”寫入定時器控制狀態寄存器（CSR1）的相應“定時器x引起的IRQ”字段來完成。該寄存器是只讀的，寫入的數據與定時器4 IRQ清除（T4IC）無關。定時器4 IRQ-清除（T4IC）寄存器用于清除定時器4引起的中斷。寫入此寄存器（位于BAR2中地址的偏移量0x3C處），將清除定時器4的中斷。這也可以通過將“0”寫入定時器控制狀態寄存器（CSR1）的相應“定時器x引起的IRQ”字段來完成。該寄存器是只讀的，寫入的數據是無關的。
Timer 2 IRQ Clear (T2IC)
The Timer 2 IRQ Clear (T2IC) register is used to clear an interrupt caused by Timer 2.
Writing to this register, located at offset 0x34 from the address in BAR2, causes the
interrupt from Timer 2 to be cleared. This can also be done by writing a “0” to the
appropriate “Timer x Caused IRQ” field of the timer Control Status Register (CSR1).
This register is write only and the data written is irrelevant.
Timer 3 IRQ Clear (T3IC)
The Timer 3 IRQ Clear (T3IC) register is used to clear an interrupt caused by Timer 3.
Writing to this register, located at offset 0x38 from the address in BAR2, causes the
interrupt from Timer 3 to be cleared. This can also be done by writing a “0” to the
appropriate “Timer x Caused IRQ” field of the timer Control Status Register (CSR1).
This register is write only and the data written is irrelevant Timer 4 IRQ Clear (T4IC)
The Timer 4 IRQ Clear (T4IC) register is used to clear an interrupt caused by Timer 4.
Writing to this register, located at offset 0x3C from the address in BAR2, causes the
interrupt from Timer 4 to be cleared. This can also be done by writing a “0” to the
appropriate “Timer x Caused IRQ” field of the timer Control Status Register (CSR1).
This register is write only and the data written is irrelevant.
