NI PXI-2546多路復用器繼電器
產品詳情資料：
NI PXI-2546多路復用器繼電器通過嵌入式網絡(luò )交換機連接到以太網。兩個以太網端口是10-BASE-T/100BASE-Tx自動協商全雙工端口，可直接連接到一條或兩條10-BASE-T/100 BASE-Tx 5類（雙絞線）以太網LAN電纜。電纜可以是屏蔽的或非屏蔽的，也可以是直接的或交叉的。請注意，端口連接到嵌入式交換機。每個端口沒有單獨的IP地址。當建立網絡(luò )鏈路時，每個端口上的LINK/ACT LED會(huì )亮起，當通過該端口傳輸數據時，該LED會(huì )閃爍。如果網絡(luò )鏈路以100 MBPS建立，NI PXI-2546則100Mbps LED會(huì )亮，如果網絡(luò )鏈路已以10Mbps建立，則該LED會(huì )熄滅。屏蔽接地連接選項卡此選項卡用于連接模塊的屏蔽接地。為此，模塊提供了帶有適用終端的導線。有關詳細信息，請參閱第2章（“安裝”）中的“CPU363、364和374屏蔽接地”一節。NI PXI-2546
connection to an Ethernet network via an embedded network switch. The two Ethernet ports are 10-BASE-T/100-BASE-Tx Autonegotiating Full-Duplex ports, which provide direct connection to one or two 10-BASE-T/100-BASE-TX cat 5 (twisted pair) Ethernet LAN cables. Cables may be shielded or unshielded, and direct or cross-over. Please note that the ports are connected to an embedded switch. There is not a separateNI PXI-2546 IP address for each port. The LINK/ACT LED on each port goes on when a network link is established and blinks when data is being transferred through the port. The 100Mbps LED goes on if the network link has been established at 100 MBPS and goes off if the network link has been established at 10Mbps. Shield Ground Connection Tab This tab is used to make the module’s shield ground connection. A wire with the applicable terminal ends is supplied with the module for this purpose. Please see the section “CPU363, 364, and 374 Shield Grounding” in Chapter 2 (“Installation”) for details.NI PXI-2546
品牌：NI
型號：NI PXI-2546
產品說明：多路復用器繼電器
特點：模塊/卡件，控制器，觸摸屏，伺服驅動器
產 品 展 示
產 品 展 
公 司 主 營 優 勢
應 用 行 業
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
