RELIANCE S-D4008-E模擬I/O卡
1.產 品 介 紹
品牌：RELIANCE
型號說明：RELIANCE S-D4008-E模擬I/O卡
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
RELIANCE S-D4008-E耦合模塊退出：1。關閉模塊2。拆下模塊3的固定螺釘。取出模塊。插入：1。插入并固定模塊2。打開模塊。7.1.3中央模塊（CU）和協處理器模塊（CM）退出：RELIANCE S-D4008-E1。擰下數據電纜插頭的螺釘。2.取出數據電纜并將其彎曲。3.拆下模塊的固定螺釘。4.完全抽出固定螺釘直到停止。5.通過彈出桿（標簽）將模塊與總線板分離，然后將其完全收回。6.請勿觸摸模塊組件！關注CMOS組件的EMC規則！插入：1。根據數據表檢查開關和跳線的設置。2.完全抽出前板的固定螺釘，直到停止。3.將模塊插入機架直至停止。4.固定螺釘。5.插入數據電纜并固定其螺釘。RELIANCE S-D4008-E
Coupling Modules Withdraw:RELIANCE S-D4008-E1. Switch off the module 2. Remove fixing screws of the module 3. Withdraw the module. Insert: 1. Insert and fix the module 2. Switch on the module. 7.1.3 Central Module (CU) and Coprocessor Module (CM) Withdraw: 1. Remove the screws of the data cable plugs. 2. Withdraw the data cable and bend it byside. 3. Remove the fixing screws of the module. 4. Withdraw the fixing screws completely till to the stop. 5. Separate the module from the bus board by means of the ejection lever (label) and than withdraw it completely. 6. Do not touch the components of the module! Watch for the EMC rules for CMOS components! Insert: 1. Check the settings of the switches and jumpers according to the data sheet. 2. Withdraw the fixing screws of the frontplate completely till to the stop. 3. Insert module into the rack till to the stop. 4. Fix the screws. 5. Plug in the data cable and fix their screws.RELIANCE S-D4008-E
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.關 于 相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
