RELIANCE 0-51865-16控制脈沖卡件
1.產 品 介 紹
品牌：RELIANCE
型號說明：RELIANCE 0-51865-16控制脈沖卡件
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
SRAM電池備用電源選擇頭（J20）RELIANCE 0-51865-16嵌入式控制器在工廠配置為使用VMEbus+5V備用電源作為SRAM的備用電源（跳線安裝在引腳1和3以及引腳2和4之間）。要選擇車載電池作為備用電源，請在針腳3和5以及針腳4和6之間安裝跳線。注意：對于沒有可選VMEbus接口（沒有VMEchip2 ASIC）的RELIANCE 0-51865-16，您必須選擇板載電池作為備用電源！注意：移除所有跳線可能會(huì )暫時禁用控制器的SRAM。除存儲器.EPROM大小選擇頭（J21）外，不要移除J20上的所有跳線。RELIANCE 0-51865-16嵌入式控制器出廠時配置為4Mbit EPROM（跳線安裝在引腳2和3之間）。要為8Mbit EPROM配置MVME162FX，請在引腳1和2之間安裝跳線。RELIANCE 0-51865-16
SRAM Battery Backup Source Select Header (J20) The RELIANCE 0-51865-16 Embedded Controller is factory configured to use VMEbus +5V standby power as a backup power source for the SRAM (jumpers are installed across pins 1 and 3 and 2 and 4). To select the onboard battery as the backup power source, install the jumpers across pins 3 and 5 and 4 and 6. Note For RELIANCE 0-51865-16 without optional VMEbus interface (without VMEchip2 ASIC), you must select the onboard battery for the backup power source. ! Caution Removing all jumpers may temporarily disable the controller’s SRAM. Do not remove all jumpers from J20, except for storage.EPROM Size Select Header (J21) TheRELIANCE 0-51865-16 Embedded Controller is factory-configured for a 4Mbit EPROM (a jumper is installed across pins 2 and 3). To configure the MVME162FX for an 8Mbit EPROM, install the jumper across pins 1 and 2.
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
