REXROTH DKC03.3-100-7-FW伺服驅動器
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH DKC03.3-100-7-FW伺服驅動器
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH DKC03.3-100-7-FW當IP DMA控制器是本地總線主控器時，報頭J26定義了窺探控制總線的狀態。出廠配置中有兩個跳線，用于禁止窺探。驗證此設置是否適合您的應用程序。9.有關REXROTH DKC03.3-100-7-FW安裝的詳細信息，請參閱特定機箱或系統的安裝程序。10.將用作162Bug系統控制臺的終端連接到REXROTH DKC03.3-100-7-FW控制器前面板上串行端口1處的默認調試EIA-232-D端口。有關其他連接選項，請參閱第2章。按如下方式設置終端：–每個字符八位–每個字符一個停止位–禁用奇偶校驗（無奇偶校驗）–波特率9600波特（MVME162FX控制器端口通電時的默認波特率）通電后，如果需要，可以使用162Bug調試器的端口格式（PF）命令重新配置調試端口的波特率。REXROTH DKC03.3-100-7-FW
Header J26 defines the state of the snoop control bus when an IP DMA controller is local bus master. The factory configuration has both jumpers in place for snoop inhibition. Verify that this setting is appropriate for your application. 9. Refer to the setup procedure for your particular chassis or system for details concerning theREXROTH DKC03.3-100-7-FWinstallation. 10. Connect the terminal that is to be used as the 162Bug system console to the default debug EIA-232-D port at serial port 1 on the front panel of the REXROTH DKC03.3-100-7-FW controller. Refer to Chapter 2 for other connection options. Set up the terminal as follows: – eight bits per character – one stop bit per character – parity disabled (no parity) – baud rate 9600 baud (default baud rate of MVME162FX controller ports at power-up) After power-up, you can reconfigure the baud rate of the debug port if necessary by using the Port Format (PF) command of the 162Bug debugger.REXROTH DKC03.3-100-7-FW
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
