WOODWARD 5466-351數字量輸入卡件
1.產 品 介 紹
品牌：WOODWARD
型號說明：WWOODWARD 5466-351數字量輸入卡件
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
WWOODWARD 5466-351互連完成后，順時針旋轉鎖定裝置至鎖定位置（3）。WWOODWARD 5466-351裝置現已完全鎖定到位，并與DIN導軌有良好的接地連接。必須將鎖定裝置放置在鎖定位置，以避免振動和/或間歇性接地可能導致的問題。拆除處理器單元連同基板使用以下步驟拆除單元連同基板：1。關閉或斷開控制器單元的電源。2.從適當的裝置底板上取下任何可拆卸的電纜。圖22。WWOODWARD 5466-351-側視圖AC 800M裝置在從DIN導軌上拆除之前必須斷開電源！不允許在帶電運行的系統中操縱CEX總線底板。在更換或移除基板之前，必須移除該段上的所有CEX模塊。將鎖定裝置旋轉至裝置基板上的滑動位置（2）。為了提供足夠的進入和移除空間，請注意，必須在與待移除裝置相鄰的裝置基板上執行滑動順序。
When the interconnection is complete, rotate the locking device clockwise to the LOCKED position (3). The WWOODWARD 5466-351 unit is now fully locked into the position and has a good ground connection to the DIN-rail. It is essential that the locking device be placed in the LOCKED position to avoid possible problems caused by vibration and/or intermittent grounding.Removing Processor Units Complete with Baseplates Use the following procedure to remove a unit, complete with baseplate: 1. Switch off or disconnect the power supply to the controller units. 2. Remove any detachable cables from the appropriate unit baseplate. Figure 22. WWOODWARD 5466-351 - Side view AC 800M units must be disconnected from the power source before removing them from a DIN-rail! It is not allowed to manipulate CEX bus baseplates in a powered and running system. Before changing or removing a baseplate, all CEX modules on that segment must be removed.Rotate the locking device to the SLIDE position (2) on the unit baseplate,In order to provide adequate access and removal space, note that the SLIDE sequence must be carried out on the unit baseplates adjacent to the unit that is to be removed.
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
