NI PXI-6251模擬輸出通道
1.產 品 介 紹
品牌：NI
型號說明：NI PXI-6251模擬輸出通道
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
NI PXI-62511.在距ControlNet BNC連接器一米范圍內為抽頭選擇合適的位置。選擇抽頭位置時，請記住引入電纜和中繼電纜的布線。它們不應靠近高壓電纜。避免過度彎曲主干電纜。2.水龍頭可以以各種方式安裝，例如使用DIN導軌或擰入合適的結構。即使抽頭未安裝在DIN導軌上，也應使用通用安裝支架，NI PXI-6251以避免與導電結構電連接。3.將分接電纜連接到BNC連接器。啟動系統之前，應測試所有ControlNet電纜連接。檢查應用連接器的拉力。4.通過將200-RACN模塊前面的兩個開關（x10和x1）轉到正確位置，定義網絡(luò )節點地址：–機架I/O。應為200個RACN選擇02-99范圍內的節點地址。–200系列I/O-單擊200-ACN模塊前面的按鈕開關。應為200個ACN選擇02-99范圍內的節點地址。–CI865-節點地址固定為01。NI PXI-6251
1. Select a suitable location for the tap within one meter from the ControlNet BNC connector. When selecting the tap location, keep in mind the routing of the drop and trunk cables. They should not be routed close to high-voltage cables. NI PXI-6251Avoid bending the trunk cable too much. 2. The tap can be mounted in various ways, for example using a DIN rail or screwed into a suitable structure. Even if the tap is not mounted on a DIN rail, the universal mounting bracket should be used to avoid galvanic connection to a conducting structure. 3. Connect the tap drop cable to the BNC connector. Before starting up the system, all ControlNet cable connections should be tested. Check the pulling strength of applied connectors. 4. Define the network node address: – Rack I/O - by turning the two switches (x10 and x1) on front of the 200- RACN module to the correct position. A node address in the range 02-99 should be selected for the 200-RACNs. – NI PXI-6251Series 200 I/O - by clicking the push button switches on the front of the 200-ACN module. A node address in the range 02-99 should be selected for the 200-ACNs. – CI865 - The node address is fixed to 01.NI PXI-6251
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
