NI PXI-8431-8端口串行接口板
1.產 品 介 紹
品牌：NI
型號說明：NI PXI-8431-8端口串行接口板
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
安裝Modbus TCP接口NI PXI-8431-8由處理器單元通過CEX總線供電，不需要額外的外部電源。使用以下步驟安裝CI867/TP867:1。將裝置安裝到DIN導軌上，請參見第65頁的“將AC 800M裝置安裝到DINRail上”和第78頁的“以單一配置安裝NI PXI-8431-8處理器裝置”。2.將10/100Mbps以太網雙絞線連接到基板上的CH1連接器。3.通過標準以太網組件將以太網電纜的另一端連接到快速以太網網絡(luò )。4.將10Mbps以太網雙絞線連接到基板上的CH2連接器。5.通過標準以太網組件將以太網電纜的另一端連接到以太網網絡(luò )。以太網雙絞線連接快速10/100 Mbps以太網雙絞線通過位于TP867上的RJ45連接器（CH1）連接。較慢的10 Mbps以太網雙絞線通過位于TP867上的RJ45連接器（CH2）連接。NI PXI-8431-8
Installing the Modbus TCP InterfaceNI PXI-8431-8is powered from the processor unit via the CEX-Bus and no additional external power source is required. Use the following procedure to install the CI867/TP867: 1. Mount the unit onto the DIN-rail, see Mounting AC 800M Units onto DINRailon page 65 and Installing the NI PXI-8431-8 Processor Unit in Single Configurationon page 78. 2. Connect the 10/100Mbps Ethernet twisted pair cable to the CH1 connector on the baseplate. 3. Connect the other end of the Ethernet cable to a Fast Ethernet network via standard Ethernet components. 4. Connect the 10Mbps Ethernet twisted pair cable to the CH2 connector on the baseplate. 5. Connect the other end of the Ethernet cable to a Ethernet network via standard Ethernet components. Ethernet Twisted Pair Connection The Fast 10/100 Mbps Ethernet twisted pair is connected via the RJ45 connector (CH1) located on NI PXI-8431-8. The slower 10 Mbps Ethernet twisted pair is connected via the RJ45 connector (CH2) located on NI PXI-8431-8.
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.fs-it.com.cn
